Painting a garage can be a difficult task for homeowners when you are painting yourself rather than when you Hire A Painter.

The other parts of the house are easy to see as either indoors or outdoors, but the garage occupies a gray area.

Can you call a place where you park your car and keep all of your outdoor supplies indoors? Is it okay to put up indoor paint? or should you use something a little bit heavier and more protective? Here is a guide to help you figure out how you can tackle the complex issue of painting your garage.

The don’ts

Do not use eggshell or satin-sheen paints on your garage surfaces. Even though your garage itself may not be directly exposed to the elements such as rain and snow, it is still vulnerable to the effects of mold and sun.

But still, using weatherproofing paint is not necessary. You shouldn’t lay down something that will push off direct rainwater or direct sunlight.

The dos

Use an oil or latex paint, especially if you are in the middle of changing your garage storage system. Still, you will have to make sure to match the paint on the walls.

You will want to to an oil-based if you gave it already because once a wall has oil-based paint on it, you will need to scuff with sandpaper and etch with trisodium phosphate if you want to get latex paint to adhere.

The Finish

Gloss finish is the best kind of finish to use in a garage. This is because it will be the easiest to clean in the long run and can lead to a sleek, industrial look.

You should avoid a flat finish, because it is easy to scuff and hard to buff out. Also, flat finishes tend to fare poorly against mold, which is common in garages.

The coverings

If you are painting over a covering like drywall, you will need to prime it with a PVA primer.

This will seal it and also allow the top coat to bind. You can use any paint on top of primed drywall, however, it must be treated before applying.

If you are using wood paneling, it will require the same attention using a shellac-based wood primer.

For cement and brick walls, you will need a concrete primer and masonry paint to hold their new paint jobs.

Best Roller for Painting Walls

Best Roller for Painting Walls

When choosing an Exterior House painter to paint your walls, the right roller needs to be chosen for your wall to make all the difference just like brushes.

Not only you get a better finish painting your walls with the roller, but the work and finishing will be faster and smoother.

Although, it seems as if cheap discounts tempt almost everyone. This is good if you want a second finish that will give you extra work.

Sincerely, a good paint roller will cut you hours of painting time while leaving a smooth, even surface. The rollers are of different sizes, from the small one (that is useful for painting the wall behind the toilet) to large (for large wall surfaces)18-inch setups, but the most commonly used size is the 9-inch rolls
Roller covers are made from a wide range of materials with different lengths.

The type and size you need depend on your project.

Choose a non-mark roller cover. Do not bother yourself with foam rollers, because they are only suitable for testing paint colors. But when they are being used on a large surface, they create a lot of small air bubbles in the paint film leaving behind a bad finish.

Good roller covers are made of phenolic moisture resistant cores or plastic which will never absorb water and lose its shape.

For the fabric naps to remain attached to the base instead of ending of the wall, they are also made with solvent resistant glues.
Abstain from roller sleeves with untreated cardboard cores, the kind sold in bulk containers, which will absorb paint, soften and lose their shape in no time.

Choose a roller cover with a short nap of about 1/4-inch or 3/16-inch if you are painting a new drywall or slab with high gloss paint. A roller cover with short nap does not hold a lot of paint, but it leaves a smooth finish with little stipple or texturing.

You can use a nap sleeves of about 3/8 inches or 5/16-inch for eggshell paint on flat already painted walls as they will hold more paint with minimum paint stipple.

A 3/8-inch nap quality roller cover is sufficiently versatile to work with most paints on most surfaces.
It is advisable to use a 1/2-inch nap sleeves for medium textured plaster and similar surfaces, but be aware that roller stipples will be visible.

This is a perfect alternative for already painted walls or ceilings that already have some texture. Most professionals recommend a nap sleeves of about ¾-inches or even more for rough surfaces like concrete blocks.

If the heap of the roller cover is less dense, it will hold more paint without splashing. To achieve excellent results, look for a roller cover that will hold paint as much as possible, however free on the wall with minimum splashes.



The roller is a very good way of managing to paint a large area, however, the ends of the roller can produce ridges which spoil the evenness of the paintwork.

In order to avoid these roller marks, below are the methods i came across in BRS Custom Painting, take the time to use the methods which will allow you to avoid it.

Get Some Good Tools

The best way to keep your paint roller from leaving marks on your wall is to buy the best. Purchase good quality paint of the sort you need to complete your project, gloss or matte paint perhaps.

Also, take the time to buy a roller which is average or good quality as a cheap roller will probably not do as well.
To keep the paint from streaking at the edge, look for a roller which has a beveled edge and a suitable core.

Cheap rollers do not have these features and their core is usually made from cardboard. It will get damp during painting, loose the shape and then cause more marks.

Mix Well

After getting your paint, start by mixing the paint thoroughly. To get the paint parts mixed together, use a metal stir stick. This will help you to avoid streaking and unevenness.

There is more chance of creating bad paint roller marks if the paint is not mixed properly.

Paint the Edges

Now, take the paintbrush and cover in the first two inches around the edge of your wall. Doing this will help in avoiding marks caused by trying to force the roller into the corner.

Apply Paint Evenly

Start using the roller by spreading a layer of paint out into the paint tray. Put the paint roller into the paint, then roll out into the tray till you have an even layer of coverage.

Try to avoid getting the ends and the core soaking with paint because this will cause them to leave roller marks. Put the paint roller onto the wall and roll it upwards and downwards with long even stokes.

Make sure you paint at a slight angle so that you are not leaving straight marks. Also, blend the next stroke into the old stroke, repeating the angled shape. Do this until the wall is complete.

How Much It Cost To Replace a Window

If you are yet to own a house for some years, you may never have had any need to know about how much it will cost to replace your windows. They are not something that enters our mode of thinking until it’s too late. By that time, rainwater is pouring into your house, drafts are blowing, and visitors are commenting that your windows need to be replaced. Some homeowners who have been through the replacement window installation process will say that they care to repeat it because of what they are benefiting from it. After all, it is necessary to invite 3-4 companies into your home to give quotes, and then invite one of those companies back to spend 3 or 4 days installing the windows.

There are countless reasons to replace the windows in your home: a new set of windows can give your house a subtle facelift. Replacing your windows with a larger one makes way for more natural light and a better view, and newer, energy-efficient windows can save you an average 25% on your energy bill.

Window varieties are grouped according to how they operate. How much it cost to replace a window depends on the type and quality of the window you need. When choosing one, you must put into consideration the size, and the function of the window, as well as the look you want to achieve. The types of windows that are commonly installed and replaced on a house include: Single-hung windows ($175-$350 per window), Double-hung windows ($300-$800 per window), Sliding windows ($325-$1200 per window), and Casement windows ($275-$750 per window)

The average cost of replacing a window is in the range of $300 to $700 per window. This believes that the replacement window is going into an existing and structurally sound and of a high-quality frame on a ground floor. Below are the factors that are affecting cost:

  1. The need to alter an existing structure
  2. Double or triple-glazed windows
  • Insulating gas in double or triple-glazed windows
  1. Exterior dressing
  2. Remoteness of the site location
  3. Time demands on the contractor
  • Unforeseen structural deficiencies
  • Profit: A Contractor has to make money to stay in business just like any other people. This the area where the greatest variation in price occur, with some bids including a profit margin of 65%-80% or higher and the typical range falling between 25-45%. The more challenging the conditions of the area, the more the contractor may charge.

Three most common reasons a basement leaks

Credit: St. Louis basement waterproofing kind of project

Credit: St. Louis basement waterproofing kind of project

If you have ever experienced leakage in your basement, you may understand how serious the problem can be. On top of the issue of standing water, you may have to deal with the potential of damage to your belongings and molds. If you would like to protect your home basement leakage, you will need to understand the common water entry points. While it is important to contact a waterproofing professional to do the job, you also need to educate yourself on the causes of the water problems and how the current situations can stop it in future.

Your basement could be one of your favorite rooms or it could just be a room that you use to store things. Whatever the case, water will try to get into the room and you will also need to keep it out. Here are some of the reasons why your basement may be leaking water.

Basement leak from top of wall

It is possible for water to leak into the basement/ foundation wall if the ground is near level or even sloping into structure. When you have rain water draining towards your home instead of away from it, there are high chances that the water will find an entry-point into the basement. This is a common problem in the older homes even though new homes can also experience this problem. Perhaps all you will need to do is to look into the gutter system of the house. If the downspouts aren’t long enough or slants towards the home, this could result in them discharging water into your basement.

The soil around the home will get settled over time in comparison to the surrounding soils that remains undisturbed. When the soil around the house settles, it can create low spots through which water drains into the house.

Leaks in window wells

If you have window wells around the basement, these can allow sunlight to get into the room, add to the décor of the home on top of keeping water and soil away from the window. While these can serve well to keep away ground water and rain water where necessary, the window well may be unable to function properly if the entire drainage isn’t working.

Overflowing gutters can result in disruption of the window well. If there is obstruction in the gutters, rain water can overflow and gush out. This can cause the window wells to fill with water. Therefore, if you have basement leaks, it is important to check the gutters to ensure that they are clear and the downspouts are draining away from the well. You should also ensure that the windows are installed properly and they have their own drainage system that is linked with the foundation drain.

Basement wall cracks

Basement wall cracks are some of the most serious problems in regard to leaking basements. This is due to the fact that the issue doesn’t stop by just fixing the crack. You will need to determine the cause of the crack to ensure that more problems don’t crop up. There are high chances that the basement crack was as a result of pressure. No matter the cause of basement leaks, it is important to consult a professional.

Three Things to Look For When Picking a Foundation Repair Company

The foundation is the most important part of your home. Therefore, when it shows signs of distress and needs repair, you cannot just hire any Tom, Dick, or Harry to fix your foundation problems. There are many foundation repair companies out there that claim they know what they’re doing – but do they?

You have to take into account a number of factors when selecting a contractor. You cannot trust a company simply because it advertises widely on the Internet or in the yellow pages.

Are They Licensed and Insured?

A legally valid work permit and prove of insurance is critical to helping ensure that the contractor you are hiring doesn’t indulge in unscrupulous practices.

You can even check out a contractor’s track record, past history and credentials on the licensing board of your city or town. Proper insurance coverage ensures that you are not held financially liable for any worker accident or injury that takes place on your premises.

Get Multiple Quotes

It is wise to ask free quotes/estimates from several contractors. You don’t have to go overboard, just get 3 estimates. It is also wise to compare their terms and conditions as well as the materials they will use. Price should not always be the most determining factor.

Written Agreement

Your foundation repair contractor should provide you with a written and signed agreement that explains all the terms and conditions in details. This helps to prevent misunderstandings and miscommunication later on. Read through the written agreement thoroughly and ask for clarifications if you have any doubt.

Always pay special attention to the guarantee clauses. Try to pass through the fine print and understand the contract before signing on the dotted line. Beware of contractors who create pressure on you to sign the agreement right away.

repairing a foundation

Credit: Repairing a foundation in St Louis

Previous Complaints

When checking out a potential contractor’s previous customer complaints, you have to understand that it is virtually impossible for any contractor to please all his previous clients.

However, you still have to pay special attention to how poorly the work was executed, whether it was left unfinished or not, whether the contractor refused to honor the warranty, disputed the warranty coverage, or delayed fixing a problem that cropped up during the warranty period.

Many foundation repair contractors’ damage sprinkler systems, plumbing, landscaping, and other property features while doing the repair job.

Also, check out how well the disputes were resolved and if the problems were fixed. While hiring a foundation repair contractor, remember to grill about the issues mentioned above and question them about their work procedure and work ethics. If you sense anything fishy or do not feel that, the contractor is trustworthy enough, move on to another contractor.

Danger Signs

Beware of outdated credentials and absence of ID. You should also be wary of hiring a contractor who demands upfront payment before starting work and offers discounts for clients willing to pay cash. These are tax evasion tactics.

Another danger sign you should be aware of – your foundation repair contractor should not ask you to obtain building permits. Avoid companies that refuse to grant referrals.

Different types of foundation cracks

At the point when splits show up in dividers, it is frequently an indication of establishment issues or harm. Ordinarily the issue is brought about by establishment shrinkage, soil extension or settlement. Seismic tremors can bring about splitting also. Where the split is happening, its size and shape can let you know a considerable measure about the issue. Knowing how to “peruse” them can help you focus the reality of the circumstance and what move to make.

It is not phenomenal to discover minor splitting in solid establishments, potentially demonstrating a requirement for solid establishment repair. This is on the grounds that solid therapists as it cures. Curing is not simply the aftereffect of water misfortune, it is likewise a substance response. The measure of shrinkage that will happen relies on upon numerous components, for example, the kind of solid that was utilized, the temperature at the season of the pour and how much water was utilized.

These are normally thin, vertical breaks that show up haphazardly all through the establishment. They can go long from several inches to the whole tallness of the divider. On the off chance that the cement was mistakenly or ineffectively blended, the splits will have a tendency to be bigger. The degree and attributes of the breaking can likewise be impacted by the utilization (or need) of steel fortifications. Shrinkage breaking will ordinarily stop once the cement has been cured.

Establishment breaks happening in a more seasoned building ought to be of more concern. Specifically, be watchful for vertical divider breaks that turn out to be detectably bigger in a brief time of time. In spite of the fact that the breaking may be the aftereffect of settlement, it can likewise be a pointer of more genuine establishment issues. Splits that are more extensive at the top than base can be risky also, particularly in the event that you discover them close to the closures of a block divider.

By and large, divider breaks that have a more extensive base than top are brought about by settlement. In the event that there is an excess of settlement, there may be hidden establishment issues that should be tended to. Contact a prepared establishment foreman in the event that you have worries about this sort of breaking, particularly on the off chance that they are showing up in a block divider, to check whether foundation crack repair is required.

Top 3 benefits of basement waterproofing

If you would like to protect the health of your family and value of your home, one of the most important things that you will need to do is to solve basement problems. A wet basement can smell and feel nasty and can pose a great risk and even affect the value of your home. If left unchecked, basement moisture can ruin walls and floor, cause molds and even result in damage to the roofing. There are certain wet basements that can easily be cured by clearing gutters and diverting the gutter water from foundation. However, if the problem is from other areas such as water flowing towards the house, backing up from a storm drain or penetrating from underground, you will need to take more serious measures. There are many benefits of basement waterproofing. You may not even be aware of some of them when you decide to do basement waterproofing. The top 3 benefits of waterproofing a basement includes:

Better energy efficiency

By doing repairs to your basement and filling cracks, it is possible to save a good deal of money on your electric and heating bill. When there are small spaces in the basement, warm air will escape and cool air will get in. This will cause your heating system to work harder so as to keep your home in a comfortable temperature. With basement waterproofing, you will have these spaces and cracks filled causing your heating to take a small break from warming your home during winter.

Increase space and value of your home

Many people consider the basement to be nothing more than just an old and musty storage space where junks can be placed and laundry done. This is without doubt the wrong ways of looking at things and you should view the basement in terms of the square footage. This way you will be able to see that the basement account for an entire floor and can add up to a 1/3 or even ½ of the total space in your home. Therefore, you can see the amount of space that is wasted. When you waterproof your basement, you will be able to add healthy and usable space to your home.

The presence of molds can cause a musty odor and this can lessen the value of your home. If your home has a structural damage as a result of a damaged foundation, it will definitely fall in value. With basement waterproofing, it is possible to prevent these damages or even stop them from occurring and this can increase the overall value of your home. If you have plans to sell your home in future, you should consider seeking the services of a basement waterproofing company.

Avoid heath risks

It is clear that humidity and water cause the growth of toxic molds. However, you may be surprised to learn how easily and quickly this can happen. When there is conducive atmosphere, toxic molds can grow in a period of 24 and 48 hours. This can be scaring to know especially when the cause is as a result of minor basement leakages. Therefore, basement waterproofing is something important that should not be ignored.

Underfloor-Heating – Much Simpler Than It Sounds


There are, undeniably, some things in life which are a little complex, but there are also some very simple concepts which might sound far more intense than they actually are. Of course, if we had the option or the time, surely we would all be more than happy to have certain changes made to our homes, but more often than not we will find ourselves putting off what is actually a very simple and time saving process simply because we expect it to be something of a challenge and one which would disrupt our lives for longer than is strictly necessary.

Still, there are many simple alterations and improvements which you could make to your home which could benefit you in wide range of ways.

For example, if you are looking to protect yourselves from the cold weather which is, thankfully, a long long way away (allowing for plenty of preparation time), then you might well want to think in a little more depth about the possibility of underfloor-heating.

But wait, is that a negative thought creeping into your head where underfloor-heating is concerned? If so, let us reassure you; underfloor-heating and the process of having this concept introduced into your lives installing common underfloor heating kits like these from will not take anywhere near as long as you might have thought not only possible, but probable.

Yes, more and more people are turning to underfloor-heating as a way to heat their homes, but what is interesting is the fact that many individuals ignore the possibilities that underfloor heating can provide, simply because they expect the fitting process to be largely disruptive and generally a pain in the backside, not to mention expensive!

Well, the best news we can offer you here should hopefully reassure you a touch too! See, as complex a process as it sounds, in the vast majority of cases, underfloor heating can be installed in a room in just a few hours.

The general perception of underfloor heating involves floors being dug-up, pipes being placed and all other sorts of hugely disruptive misconceptions. Thankfully, the process is nothing like this and shall allow you to get on with your lives with ease.

So, why let the potential benefits of underfloor heating slip away simply because you expect it to be a problematic process?

The truth of the matter is that underfloor-heating is a doddle to install and the potential perks are certainly worth an hour or twos disruption.